^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD). ***Acura ZDX V6-3.7L Technical Service Bulletin # 11-029 Date:

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD). ***Acura ZDX V6-3.7L Technical Service Bulletin # 11-029 Date:

110930

Body - Front Inner Fender Warped/Not Flush With Fender

11-029

September 30, 2011

Applies To:

2010-11 ZDX - ALL

Front Inner Fender Is Warped, Does Not Fit Flush Against the Fender

SYMPTOM

57

The front inner fender is warped, creating a gap at the rear of the front wheelwell.

PROBABLE CAUSE

The inner fender warped in high temperatures.

CORRECTIVE ACTION

Replace both front inner fenders, and install fender stiffeners using new screws.

PARTS INFORMATION

Left Inner Fender:

P/N 74151-SZN-A00

Left Fender Stiffener:

P/N 741 52-SZN-A00

Right Inner Fender:

P/N 74101-SZN-A00

Right Fender Stiffener:

P/N 741 02-SZN-A00

Screw, 5x20 (12 required):

P/N 90103-TA0-000

TOOL INFORMATION

Push Pin/Grab Rail Cap Pliers:

T/N 07AAC-001A100

WARRANTY CLAIM INFORMATION

The normal warranty applies.

Operation Number: 8131J8

Flat Rate Time: 0.6 hour

Failed Part: 74151-SZN-A00

Defect Code: 00401

Symptom Code: 00101

Skill Level: Repair Technician

58

REPAIR PROCEDURE

NOTE:

^ Put gloves on to protect your hands.

^ Take care not to scratch the body.

1. Raise and support the vehicle.

2. Remove the wheel nuts and the front wheels.

3. Remove both front inner fenders:

^ Remove the nine screws.

^ From under the front bumper, remove the bolt and detach the two clips securing the bumper and the inner fender.

^ Using the push pin pliers, remove the 11 remaining clips securing the inner fender to the body.

NOTE:

Discard the six screws and use the new ones with a smaller head.

4. Install the new inner fender and stiffener:

59

^ If any clips are damaged or stress-whitened, replace them with new ones.

^ Push the clips into place securely. Torque the bolt to 7.4 N.m (5.5 lb.ft)

What's the Firing Order Of Acura 3.2 TL

Left/right, the torque distribution stretches all the way in which from 100/0 to 0/100: all to none, utilized to wheels on either aspect. All 2.4L fashions are powered by a 206-horsepower 2.4-liter engine that drives the entrance wheels by way of an eight-pace, dual-clutch computerized transmission. It's located on the top of the valve cover in direction of the rear of the engine. 4 black sq. modules on each valve cowl with wires going to them along with a plug. Plug the ABS wiring harness in. There are a couple of forms of solenoids in an car. Attempt eradicating battery cables for a couple of minutes. Add 4.5 quarts of the proper weight oil, begin the engine and run for 2 minutes. Saying that, in case your car is designed to run on 93 octane then utilizing 87 octane will be detrimental to the engine because of pre-detonation that might be caused by working the decrease octane fuel.

When the test engine mild is on, the computer units a fault code.Most auto parts stores will check this code free of charge and inform youhow to fix it. Acura tl ninety nine code 1457 the way you fix it thank? What size wiper blade suits a 2005 Acura TL? What is the headlight bulb size of a 2002 acura 3.2 TL? The peak of the 2002 Acura TL is 4 ft. The above sentence came straight from the 2001 Acura TL service handbook How do you exchange a starter on an 97 Acura 3.2 TL? To find out the spark plugs wanted consult your owner's manual or a automotive restore guide. We simply had ours reset in the present day and the man used a pc hooked up to our automobile. This is the reset code. Repeat if mandatory. How do you reset the upkeep mild on a 2008 civic? The sunshine is on because you've got disabled the Vehicle StabilityAssist (VSA).

It is at all times finest to have the producer's suggested grade of gasoline.. This text is an attempt to help you get that finest automobile. It should be a choice I get to make. Make sure to do this! Make sure you've gotten all of your codes before doing this although. I have an 86 4 cyl and a 95 6 cyl. The calipers are mounted on brackets which have two bolts attaching them to the steering knuckles. I actually recommend having a shop do this as they have power steering flushing machines that simply have 2 hoses that go in the fluid resevoir. How many valence electrons does Xenon have? If you're shopping for oil, filters, chemicals, and many others. Autozone or Superior is an effective place to save cash, but there is a motive their parts are cheap. Just remove any screw and clip that hold the rocker in place. If you're about to grab a screw driver or a pair of pliers then you're about to break one thing.

Pink sockets are half number 78181-S0K-A21, 9.5V 1.14W bulb. Pull back each the bulb and the security protecting. 40,000. What are costs on truck masses? There are several Acura models to choose from and also you wish to know precisely which one you may afford. My ownpersonal view is that point is best spent on parts that havereal existence and questions will be asked the place there are factuallybased solutions! Significantly better shifting afterwards. When this is finished all the belts will be off the automobile so its a logical time to replace all the belts. EsKIRuK7his What number of belts does a 98 acura 3.2 tl has on the motor? What number of belts does a 98 acura 3.2 tl has on the motor? In accordance with the EPA, the inside quantity of the 2007 Acura TL is 110.Four cu.ft.. God Bless How do you modify brake pads on a 1993 Acura Integra? What's the buzzing sound that comes from the brake modulator on a 96 acura tl 3.2?

What's the Firing Order Of Acura 3.2 TL

You'll have over stuffed the reservoir and the fluid will develop because it heats up and come out the cap. What's the that means of signing out from Twitter? The couple of cosmetic upgrades for the 2012 mannequin really make the automotive stand out and look special. Acura launched the TLX in 2015 to replace its TSX and TL sedans, aiming to combine the enchantment of each vehicles in a single mannequin. The Acura TLX was a brand new model for 2015 that changed both the TSX and TL. A extremely nice factor in regards to the TSX is that it has many luxurious options that come normal with the car. It is unlawful to take away the converter from any automobile. Is it simpler to take away the again seats to change a gas pump than to drop the gasoline tank in a 1999 acura tl 3.2? \nRemove the plastic cowl from a prime of the engine it has 4 bolts.As soon as it's take away you will notice 6 coil packs,positioned 3 on the Left and 3 on the best side prime of engine. Then, while you go to that listing, you'll solely see their tweets. You have to a flashlight to find them.

You might have an extension for your ratchet if the spark plugs are deep-set or circuitously accessible. The way I did it it's essential run 4 wires, 3 to the toggle swap, one from the bottom of the fan, to the ground wire of the battery. The ground clearance of the 2001 Acura TL is 0 ft. Rest service due soon light on 2006 Acura TL B1? It is basic service which both oil and filter are modified, along with tire rotation and checking of fluid levels and some other items checked. You need to take it to the service anyway, let's asume that they know for what to look. It is positioned next to the proper-most coolant passage (look for the two massive radiator hoses, it's the lower hose.) The connector is round and grey and has one black wire and one green wire main into it.

For those who look on the vaccum routing sticker it's going to show it is approximate location. The NSX racer will be towed to the SEMA sales space by a modified 2017 Acura MDX that's been lowered and is riding on 20-inch wheels pulled straight from the Acura accessory parts catalog. The upper octane fuel will provide no extra energy, fuel economy, or every other benefit in any respect. Does the o2 sensor have something to do with the catalytic converter on a ninety nine Honda accord? 1 particular person found this useful How a lot horespower does an Acura TL have? The 2002 Acura airbag management module is positioned on the firewall inthe engine compartment. The radiator fan change is just under the intake manifold (and above the oil filter), located at the rear of the engine block. They're able to do the mandatory changes to your supercharger to offer the optimum volume of air to the engine.

The plugs are in the middle after you took the top off. Then push the other finish down into the engine, exchange thecovers and you might be good to go. The place are the radiator fan switches on a 1997 Oldsmobile Cutlass Supreme? The fan motor is connected to the fan blades. The 2009 Acura TL takes 26" drivers and 19" passenger facet wiper blades. The entire process takes a few half an hour per aspect. How do you modify the sunshine bulb for the clock on a 2003 Acura 3.2 TL? What kind of transmission fluid for 2003 acura tl? Good luck. How do I repair the OBD II connector issues for 1997 Acura 2.5 TL? 2 sq. relays, the one inboard my 1997 has the relays in the glovebox behind a small panel on the left The place is the EGR valve positioned on a 1996 Acura TL 3.2? Both behind the catalytic converter (canister wanting factor under the physique of the automobile) or in the opposite manifold..i have a 2.5 not sure if 3.2 has 2 manifolds How do you reset upkeep gentle on acura 3.2 tl?

Acura is one among the most well liked promoting automotive brands in the USA and many other international locations. The rapper Notorious Big typically rapped about driving in his Acura Legend. How do I substitute the PCV valve in my 1990 Acura Integra? Which Is best: Acura NSX or Nissan GT-R? No dip stick. On the trans oil pan there is two drain plugs, one high one low, fill thru the higher plug. In case your thinking of buying a new auto, low-cost insurance ought to be one of the factors you consider. Where is the PCV valve in a cadillac deville situated? The place is the placement of a beetle PCV valve? Answer . the kind s has an even bigger v6, that pushes 160 hp (for the 2003 models like mine) . Reply . Excellent under the steering wheel, behind the plastic covers, you'll discover a black rectangular unit with a blue push swap. This answer is for a type-s.

What's the Firing Order Of Acura 3.2 TL

Most likely however you need to use the grade really helpful in the homeowners guide. When it says to use premium gasoline in a Land Rover, you must take it precisely for what it says. Original equipment catalytic converters use an expensive platinum catalyst. How many catalytic converters are on a stock 8 cylinder engine? The PCV valve on a VW Beetle engine is located about half means down the crankcase, nearly centre line. Now could be the time to threat the wiring throughthe headliner gap and take the mirror down. Acura redesigned the MDX鈥檚 twin-screen interface with more menus and command buildings, featuring a brand new 7.0-inch capacitive touchscreen with a 30-p.c sooner response time. You save a lot of time and you do not mess up the wire system of your car with the black tape and stuff. The nostril of the automotive is being re-shaped. The infotainment system now comes standard with Apple CarPlay and Android Auto compatibility. In a 2017 First Drive, we said that with its decrease heart of gravity, the MDX Hybrid provides better dealing with in all weather circumstances particularly with the usual Super Dealing with All-Wheel Drive system. 2017 acura ilx overview, rankings, specs, prices, photographs, The 2017 acura ilx isn't lengthy on glamor, but it's a targeted and comfy compact sedan on the first rung of the luxury ladder.

How do you change a Acura TL 3.7 TL? How do you alter the spark plugs in a 1991 acura integra? How do you alter cabin air filter 2003 acura? How can you inform if the fuel pump is dangerous on 1997 Acura TL 3.2? Good luck. Methods to replace a fuel pump on a 1998 acura tl? How do you substitute rack and pinion on a 2003 acura tl 2.3? What does the M stand for in an Acura TL shift? How do reset a upkeep mild 2006 Acura RSX? How do you reset maintenance mild for Acura 3.2 TL? The new face of ILX emanates from Acura鈥檚 signature Diamond Pentagon Grille, framed by 7-aspect Acura Jewel Eye鈩?LED headlights and a extra sharply sculpted hood. A more economical may very well be efficient in addition to we have now to contemplate the equipment itself. I've an Acura CL. What is the engine oil capability for a 2005 Acura TL?

No , the 3.2 liter V6 engine in a 2002 Acura TL ( IS an interference engine ) 2000 Acura TL engine oil capability? Were do you join the plug for the examine engine gentle in a acura integra 1996? 2.5 half if its ruinend get a brand new one if it needs it The place is a gasoline relay in a ninety seven acura 3.2 tl? What do you get when you smoke? The EPA vary estimate for the 2006 Acura TL is 307.Eight mi. Completely different model relying on cruise control Where is the starter situated on a 1996 Acura TL 3.2? When its aligned with the intermediate wheel timing mark (there is an arrow on the cowl as a trace) should intersect as seen from the suitable wheel properly. Mark the springs L and R earlier than you proceed. Supplemental Restraint System gentle ) indicatesthat a problem has been detected with the air baggage , if the light stays onor flashes .

In between air filter and throttle physique. Some individuals, and even dealers confer with the rear ones as solely resonators, as they cut back much more the sound and vibration of the air coming out. Utilizing periodicity, lithium has the best ionization energy out of those parts subsequently it is going to release extra power when reacting (making it more reactive.) As properly, fluorine would relatively acquire electrons than misplaced electrons. Our forefathers thought that private accountability and freedom was more necessary than legislating individuals into oblivian. Waiver of legal responsibility. I, declare no responsibility for any damaging incidents that may occur from this information. You'll have toremove some plastic panels to entry it. Renowned Honda high quality combined with European styling, luxurious, and engineering have fueled Acura's success so far. A easy explanation may be discovered within the proprietor's guide, but assuming you don't have it (like me jeje). This ring can pop open, so play with it and open it with the intention to move the meeting.

DM' stands for 'Direct Message' - a message you could ship to somebody privately with out it showing on your timeline. New spark plugs should not must begapped as they arrive preset from the manufacturing facility. With the breather chamber cowl off, you may see the PCV valve screwed into the valve cover. If one meticulously maintains thevehicle and drives sensibly, they could achieve 250,000 to 350, 000miles before requiring a rebuild. If you take away the T-stat pay attention to the position of the T-stat. This places you within the commanding place. Mounted on high and inside the gasoline tank. Remove the round rubber stopper from behind the assembly to expose the lamp. Has a rubber hose that connects to the intake manifold. In base models, the 8-speaker audio system is rated at 266 watts. \nWell if you're talking about reseting the system when the service lite is on, that is straightforward.

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura RL V6-3.7L Technical Service Bulletin # 08-029 Date:

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura RL V6-3.7L Technical Service Bulletin # 08-029 Date:

110928

Navigation System - Set-Up/Controls/Overview

08-029

September 28, 2011

*Applies To :

2009-12 RL - ALL*

2009-12 RL: TQI of the Navigation System

(Supersedes 08-029, dated December 8, 2010, to revise the information marked by the asterisks)

*REVISION SUMMARY

In Applies To, 2012 models were added.*

BACKGROUND

This bulletin provides information for the TQI and testing of the navigation system. These topics are covered:

^ Navigation System Controls

^ Voice Control System

^ Navigation System Setup at the TQI

^ Resetting the AcuraLink Control Unit to Clear DTCs

^ System Limitations

58

^ Map Coverage Areas

^ Hawaii System Setup

^ AcuraLink Real-Time Traffic Information

^ AcuraLink Real-Time Weather Information

^ Ordering a DVD

For more information about the navigation system and its operation, refer to these resources:

^ Advanced Technology Guide

^ Online University - Use the keyword NAVI for more information about the navigation system.

^ Navigation Manual - In addition, to the one that comes with the vehicle, the navigation manual is available online. Select Search by vehicle, then

enter keywords NAVIGATION MANUAL.

WARRANTY CLAIM INFORMATION

None. These procedures are considered part of the normal TQI.

NAVIGATION SYSTEM CONTROLS

VOICE CONTROL SYSTEM OPERATION

Voice recognition is controlled by the NAVI TALK and NAVI BACK buttons on the steering wheel. This is the primary way to give commands to

the system. The system buttons and interface dial are a secondary method to use the navigation system.

59

NAVI TALK button - Press and release this button on the steering wheel to activate the voice control system. After pressing and releasing TALK,

wait for the beep, then speak the command.

NAVI BACK button - This button has the same function as the CANCEL button. Press this button to return to the previous display. After the

previous display appears, the system prompts you for a command and sounds a beep. Press the NAVI TALK button to say your next command.

Improving Recognition

If the system does not understand your voice commands, refer to Improving Voice Recognition in the navigation manual.

NOTE:

^ The navigation system won't respond if you have activated the HFL TALK button. Press the HFL BACK button before using the navigation

system.

^ You must be in the driver's seat to use voice commands with the navigation system.

^ If you speak a command with something in your mouth, with a heavy accent, or have a high-pitched voice, the system may misinterpret your

voice command.

NAVIGATION SYSTEM SETUP AT THE TQI

The navigation system is basically ready to use when the vehicle is delivered to the dealership. Since the system interfaces with other systems in the

vehicle, it is important to ensure that all of the systems are initialized so they will work properly for the client. To initialize the system, follow this

procedure.

1. Do the normal TQI of the vehicle, including the audio system. The navigation system voice will not function until the 5-digit, anti-theft code for

the audio system has been entered.

2. Verify that the MID (multi-information display) shows Welcome DRIVER 1 or Welcome DRIVER 2 when you first get into the vehicle and turn

the ignition switch to ON (II) with the driver's door closed.

NOTE:

If the MID only shows Welcome when you turn the ignition to ON (II), the remotes are not linked with the vehicle and any changes made to

the setup settings cannot be saved.

You must link the remotes before proceeding. See the body electrical section of the 09-11 RL Service Manual, or online, enter keywords

KEYLESS DESC, and select Keyless/Power Door Locks/Security System Description from the list.

3. If the navigation factory In-Line diagnosis screen (shown) is displayed, do the following. If not, go to step 5.

^ Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time until the Select diagnosis item screen comes up. Then

release the buttons.

^ Press and hold the MAP/GUIDE button for at least 15 seconds.

^ Select Complete on the screen, then select. Return twice to exit the diagnostic mode.

4. Start the engine, and drive the vehicle outside, away from buildings, tall trees, and power lines. Then enter the 4-digit security code for the

navigation system. The code is on the Navigation Anti-Theft Code card.

NOTE:

There are two code labels and a plastic code card located in a small plastic bag in the glove box.

^ Attach one of the labels to the code card, put it in the plastic bag, and return it to the glove box.

^ Attach the other label to the TQI repair order, or put it in the plastic bag, and return it to the glove box for the client.

60

NOTE:

Never attach a label to the side of the glove box or other location where both the serial number and code are easily visible. This defeats the

purpose of the anti-theft protection.

If the code card is lost or unavailable, you can get the code from the iN (Interactive Network) using the navigation system serial number. The

system serial number can easily be obtained without removing the navigation unit. To get the serial number and the code, do this:

^ Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time.

^ At the Select Diagnosis Items screen, select Detail Information & Settings, select Unit Check, then ECU INFO. The system runs a brief

diagnostic, then the navigation unit serial number is displayed at the bottom of the screen.

^ Use the navigation Anti4heft code inquiry option on the iN to look up the 4-digit navigation anti-theft code.

^ If the code does not work, call the warranty department. Do not call Tech Line.

5. The following instructions appear on the screen to indicate the system is initializing (determining its location from the GPS satellites). Follow the

on-screen instructions.

NOTE:

The average initialization takes about 10 minutes, but it can take as long as 45 minutes. If initialization completes within 10 minutes, the

display changes to the globe screen.

6. If the system does not initialize within 10 minutes, a second screen, shown below, appears. The system is still initializing but will not

automatically exit to the globe screen when the initialization is complete. Do not immediately follow the instructions on the screen. After 30

minutes, try restarting the vehicle to see if the navigation system completed the initialization. If not, follow the instructions on the screen.

NOTE:

The initialization screen may appear after battery voltage to the navigation control unit has been disconnected for more than 5 minutes. If this

occurs, follow the on-screen instructions. If you are still unable to obtain GPS initialization, refer to the service manual for diagnostic

information.

7. When initialization is complete, the disclaimer screen appears. Select OK.

NOTE:

Do not enter a destination yet. In order for the navigation system to calculate a route, it must align the current location to a mapped road (map

matching). This happens when you start driving on a digitized road.

8. Make sure that the XM(R) Radio dealer demo account is active by tuning to several channels within the full XM lineup. To see the full list of

XM channels, go to www.xmradio.com.

NOTE:

For 2009-12 RLs, XM Satellite Radio AcuraLink Real-Time Weather, and AcuraLink Real-Time Traffic are free for the first 3 months. After

3 months, clients must subscribe to XM radio, AcuraLink Real-Time Weather, and/or AcuraLink Real-Time Traffic to continue receiving

coverage by calling 800-852-9696, or online at www.xmradio.com. They will need their XM radio ID (displayed when you tune to channel

0) and a major credit card.

61

9. Drive the vehicle at least a half-mile from your dealership, and find a safe place to park. Then set the map scale to 1/20 by turning the interface

dial clockwise.

^ Make sure the VP (vehicle position) icon moves smoothly as you drive and does not jerk from one point to another. Also make sure the icon

points in the direction the vehicle is traveling; it does not "dog track" or spin.

^ Make sure the VP icon smoothly follows the vehicle's maneuvers as you make turns.

^ After driving a few hundred feet on a road that is displayed on the map, the name of the road you are driving on should appear across the

bottom of the screen.

NOTE:

Refer to the service manual symptom troubleshooting if the navigation system fails to map-match after the vehicle is driven for more than a

couple of miles on a displayed road.

10. With the map screen displayed, press and release the NAVI TALK button.

11. When you hear the beep, say "find the nearest Acura dealer." The system should display a list of Acura dealers.

12. Turn the interface dial to highlight your dealership, then push in on the ENTER button.

13. On the Calculate Route to screen, select OK.

14. The system then calculates a route and displays it as a blue line. If you are in a rural area with unverified roads, you may see a blue vector line

pointing in the direction of your destination or a blue/pink dotted line.

15. Follow the voice guidance back to your dealership. The voice guidance should work even with the audio system turned off.

16. With the map screen displayed, check the system interaction with the audio system and the upper display. Press and release the NAVI TALK

button. After the beep, say XM channel 122." The upper display should change to XM channel 122 and show CNN News.

17. With the map screen displayed, check the system interaction with the climate control system. Turn on the climate control system by selecting

AUTO. Then press and release the NAVI TALK button. After the beep, say "temperature 68 degrees." The upper display should change to 68

degrees.

18. The time shown by the system should be correct the system gets it from the GPS satellites.

For areas that do not follow daylight saving time, you may have to adjust the time settings. Go to clock adjustment in the Setup screen, and set

Auto Daylight to OFF.

If your dealership is located near a time zone boundary, set Auto Time Zone by GPS to OFF. The clock then keeps the "home" time if the client

routinely drives across the time zone boundary.

NOTE:

^ If the MID showed only Welcome when you got into the vehicle and turned the ignition switch to ON (I I), the remotes are not linked with

the vehicle, and the setup settings will not be saved.

^ You must link the remotes before proceeding. See the body electrical section of the service manual, or, online, enter keywords KEYLESS

DESC, and select Keyless/Power Door Locks/Security System Description from the list.

19. Press the DISPLAY MODE button to verify that the display changes between the Day, Night, and OFF modes.

20. If your dealership is located in a metropolitan area that has traffic incident or traffic flow data available (see ACURALINK REAL-TIME

TRAFFIC INFORMATION), do this:

^ Select one of the traffic map scales (1/2-, 1-, 2-, or 5-mile scales) by rotating the dial.

^ Use the interface dial to scroll to the downtown area of your city. Freeways and other main roads should show traffic flow data as red,

yellow, or green lines for traffic flow in one or both directions on the road.

^ Small diamond-shaped "traffic incident" icons may be shown. If so, scroll over an icon and press in the interface dial to see the details.

^ Partially displayed traffic data does not indicate a problem with the navigation system. Traffic flow and density varies from day to day and

from one road to another. If your area has traffic, but it is not displaying on the screen, refer to the navigation section of the service manual.

21. Press the SET UP button, or use the voice control system and say Set up." Then verify these settings:

^ Volume is set to the midrange.

62

^ Brightness is set so the display can be seen in bright sunlight.

22. In the setup mode, select More, then Personal Information, then Previous Destinations. Follow the screen prompts to delete all previous

destinations except your dealership.

RESETTING THE ACURALINK CONTROL UNIT TO CLEAR DTCs

AcuraLink is a two-way communication system between the vehicle and American Honda, using the XM satellites. It works with the vehicle's

navigation system, the HandsFreeLink system, and the audio system.

When the No.15 fuse is removed during vehicle shipment, the AcuraLink control unit sets DTCs. These DTCs need to be cleared during the TQI

using this procedure:

1. Start the engine.

2. On the navigation system disclaimer screen, select OK by pressing the interface dial. (The interface dial is the large knob at the center of the

dashboard. It has two parts: an outer knob and an inner selector. The interface dial is used to control several functions, including AcuraLink.)

3. Next to the interface dial, press and hold the MAPGUIDE, MENU, and CANCEL buttons at the same time, until the Select Diagnosis Items

screen is displayed.

4. Turn the interface dial to highlight the Self-Diagnosis Mode icon on the screen, then press the interface dial to select Self-Diagnosis Mode.

Allow the diagnostic to run.

5. Turn the interface dial to highlight the XM (HIP) icon on the screen, then press the interface dial to select XM (HIP).

6. Turn the interface dial to highlight the XM (HIP) Diag icon, then press the interface dial to select XM (HIP) Diag.

NOTE:

If the select diagnosis item menu screen does not appear, do this:

^ To establish communication with the navigation system, disconnect the negative cable from the battery for 30 seconds, reconnect it, then

repeat steps 1 thru 6.

^ Because you have disconnected the battery, do this:

- Reenter the audio unit anti-theft code and the radio station presets.

- Reenter the navigation system code.

- Redo the idle learn procedure.

7. Turn the interface dial to highlight the Data Reset icon. Then press the interface dial to select Data Reset.

8. Turn the interface dial to highlight the Yes icon. Then press the interface dial to select Yes.

9. Select OK by pressing the interface dial, then toggle the interface dial to the left one time.

10. Press the CANCEL button.

11. Turn the interface dial to highlight the Return icon. Then press the interface dial to select Return.

12. Again, turn the interface dial to highlight the Return icon. Then press the interface dial to select Return. This returns you to the navigation

system screen.

SYSTEM LIMITATIONS

If you think there are any problems with the navigation system during the TQI, or after installing replacement parts to repair the system, refer to

System Limitations and Database Limitations in the navigation manual. This will help you to avoid replacing components when the issue may be a

system characteristic.

The navigation system has these limitations:

^ The GPS (global positioning system) satellites used by the navigation system are operated by the U.S. Department of Defense. For security

reasons, certain inaccuracies are built into the GPS. This can cause occasional positioning errors of up to several hundred feet. If the navigation

system indicates your position incorrectly, wait several seconds until it corrects itself. The system may also correct itself after you make a turn or

cross a road.

^ The GPS antenna receives location information from orbiting satellites. Anything that blocks or interferes with the signal affects accuracy. The

63

GPS signal can be blocked or interfered with (vehicle position shown incorrectly on the map) by:

- Aftermarket metallic window tinting above or to the sides of the GPS antenna.

- Aftermarket vehicle theft location systems mounted near the navigation control unit or display.

- Radar detectors, cell phones, or other aftermarket electronic accessories placed near the navigation control unit or display.

- Outside electrical interference from overhead power or trolley lines or broadcast sources.

- Tall trees or buildings near or over the vehicle. They can cause the system to show the vehicle on an adjacent street. This should

automatically correct itself when the obstruction is gone.

^ If the DVD door in the control unit is opened or the DVD is removed, the system will reboot. Scratches or fingerprints on the surface of the

DVD can cause system errors. Always handle the DVD by its edges.

^ A DVD with a white label (Canadian vehicles may have a gray label) is used for this system. It cannot be interchanged with a DVD from a

different vehicle that has a different-colored label.

See the navigation manual for more information.

To minimize distractions, always use the voice control system to operate the navigation system while driving. Always verify the audio and visual

route information by carefully observing roadway signs, signals, etc. Use your own good judgment, and obey traffic laws while driving.

NOTE:

If the location of your dealership is shown incorrectly or needs to be changed, report it to your DPSM.

MAP COVERAGE AREAS

The map database covers the 48 contiguous United States, Hawaii, and parts of southern Canada. Coverage for the U.S. contains accurately mapped

(verified) metropolitan areas and less accurate (unverified) rural coverage. In Canada, the database covers major metropolitan areas and major roads

connecting those metropolitan areas. Coverage extends to about 100 miles from the U.S. border. A gray DVD that provides coverage for northern

Canada is also available for purchase. To order a navigation DVD, refer to ORDERING A DVD.

Detailed Coverage and Non-Detailed Coverage

Many cities and metropolitan areas are fully mapped with detailed coverage while rural areas typically have less accurate, incomplete, or

non-verified information. Refer to the Introduction and Getting Started in the navigation system manual for more information.

For a list of current detailed coverage areas by country and state/province, refer to the navigation system manual or the website. Select Model, and

Year in the drop down menu under Find Updates, then select Map Coverage.

HAWAII SYSTEM SETUP

The white navigation DVD contains maps for the 48 contiguous states, parts of southern Canada, and Hawaii. If the vehicle is sold in Hawaii or

relocated from the mainland to Hawaii, you must change the map coverage so the applicable maps are displayed.

1. Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time. The display changes to the Select Diagnosis item screen.

2. Select Detail Information & Settings.

3. Select Coverage area.

4. Then select Hawaii coverage. The system may reboot.

5. Start the vehicle, and move it to an open area so that the system can acquire the GPS signal.

6. After the system has initialized, do the map matching by driving the vehicle on a road until the road name appears at the bottom of the map

screen.

NOTE:

^ If a vehicle is relocated from Hawaii to the mainland, you must change the Coverage area to US.

^ When you change the coverage area, any previous destinations, address book, and other system settings are changed to the factory defaults.

^ XM Satellite Radio is not available in Hawaii.

ACURALINK REAL-TIME TRAFFIC INFORMATION

64

Current traffic information can be displayed by the system in many metropolitan areas. Information is displayed as traffic flow bands of different

colors on selected roads, or as diamond-shaped icons.

NOTE:

^ Traffic information is not displayed if the XM Radio dealer demo account is not active.

^ Refer to the navigation section of the service manual to troubleshoot real4ime traffic problems.

The amount of traffic coverage varies from city-to-city. The Acura website contains a link that provides an up-to-date list of the current cities with

traffic coverage and the actual roads covered within each city. The link also provides a demonstration of the system that explains traffic flow color

bands and incident icons displayed on the map. The link can be found on the website.

ACURALINK REAL TIME WEATHER INFORMATION

AcuraLink Real-Time Weather shows current local weather as weather icons on the map screen. These are different from weather related traffic

incident icons. The weather icons are:

You can also see weather warnings. Say or select Warning Map. The display changes to show weather warnings for the selected area.

ORDERING A DVD

Replacement DVDs can be ordered online at the website, then select Model, and Year in the drop down menu under Find Updates. You can also call

65

the Acura Navigation Disc Fulfillment Center. Both methods require a credit card.

For more information about ordering the correct DVD for the vehicle, refer to Service Bulletin 05-018, Navigation System Information.

What's the Firing Order Of Acura 3.2 TL

When the test engine gentle is on, the computer sets a fault code.Most auto components stores will examine this code totally free and inform youhow to repair it. For 2005, the mix of the Acura TSX elements was added by the heated mirrors, a energy-passenger seat, and satellite radio. How do you bleed the brake line on a 1997 acura 3.2 tl? The 2013 Acura TL has 13.1 cu.ft. 1993 acura radiator fan wont turn off? The fan relay on a 1996 Cavalier ought to be in the relay field. On the surface of the field in the direction of the windshield, you will notice the fourth bolt holding several wires to the air-filter field. If a spark plug insulator is cracked or broken the engine will misfire as the ignition spark will travel to the engine block (ground) as a substitute of the spark plug hole (between the electrodes). Nonetheless, if we speak in context of performance, the all new Accord Crosstour's V-6 delivers outstanding efficiency at any engine speed.

Given how quickly high-priced luxurious and performance cars like the NSX depreciate, you can likely save money with a used model instead of a brand-new one. DM' stands for 'Direct Message' - a message you can ship to someone privately without it showing on your timeline. How do you modify the parking light in a Acura TL? Push the SEL/RESET button and the Oil Life will reset to 100% and the Service Due indication will disappear What might a maintenance required gentle be indicating on a acura tl 2000? You will notice additionally a plastic strip running along the latch sill. As soon as that is all out of the way you will see the T-stat overlaying, remove it and expose your therostat. 98 acura tl 2.5 with a straight 5 engine everything stock tops out at 170 mph The place is the thermostat location in 2003 Acura TL? Some problems with the 2007 Acura TL are a power steering hose drawback, brakes wearing out extraordinarily fast, and transmission problems. 3, it fills the 1s orbital and the 2s. However only has three within the 2p, which means there may be one electron in each sublevel, so there are three unpaired pairs. There are three different bulbs that I've seen, relying on where they're on the dash and what perform they illuminate.

There isn't a temp change. Be aware: When pulling the HID, there may be 2 wires, the one which plugs into the HID and one other smaller one. I think it is known as the heater motor and has a circuit breaker and a forty amp fuse within the beneath hood fuse compartment. 14. Take away the 12mm bolts and nuts (7 I believe) attaching the plenum to the lower manifold. To remove the radio take away the mounting screws for the centerconsole. Additionally more than possible will decrease gas economy and trigger a pinging sound from the engine. Where is gas pump relay positioned for a 1996 3.2 TL? Its a good suggestion to change the timing belt and tensionor at the same time as the water pump. The dummy鈥檚 head contacted the frontal airbag but rolled to the left as a result of the seat belt allowed excessive ahead excursion of the head and torso. Will 2007 inventory Corvette wheels fit a 1988 Corvette?

Jevin IAT sensor 1999 Acura TL 3.2? 2000 Acura TL 3.2 1 particular person found this helpful Does a ninety nine Acura 3.2 TL have an IAT or MAF sensor and where is it? What is the EPA metropolis and highway mileage estimate for the 2002 Acura TL? 461.7 mi. on the freeway. You've gotten to hold down the odometer stick for like 10 seconds earlier than beginning your car continue to push it in when you start it and hold it for an additional 10 seconds.. The TSX, whereas also increasing its measurement over earlier years, is the smallest car Acura offers. The 3.5L affords the Technology package deal along with an Advance package with extra creature comforts and the A-Spec bundle, which turns the car into a sportier proposition. Our aim is to make purchasing in your next automotive as easy as possible. I now personal the automotive in NY. Two Pre-Catalytic converters proper after the engine block, and a third after the y-junction and flex pipe. What number of catalytic converters does a 2002 Chevy S10 have? What number of catalytic converters does a Ford Escape have?

The 2006 mannequin of Acura TL obtained the award for "Best Sports Sedan with Luxurious Touches" from Consumer Search. What is the cargo capability of the 2004 Acura TL with all seats in place? 4 liters Have been is the PCM located in a 2001 Acura TL? The Gates web site shows ( 3 ) , alternator , energy steering , and air conditioning How do you bleed your radiator on your Acura TL 3.2? Where is the starter on a 2003 acura 3.2 TL? The tow/haul button on the later mannequin GM trucks and SUV's change the shift factors in the transmission. Lubricate "with particular grease" all contact points the pad with contact. Reply . You want to make use of Honda power sterring fluid. Answer . You buy rearview mirror adhesive from a auto retailer.. 8mm or 10mm bolt and it isn't very straightforward to get to. 10.3 in. (70.Three in.)1 one-contact power windows broad.

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura TSX V6-3.5L Technical Service Bulletin # 10-017 Date

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura TSX V6-3.5L Technical Service Bulletin # 10-017 Date

110708

Audio System - No XM SoundXM Stations Are Displayed

10-017

July 8, 2011

Applies To See AFFECTED VEHICLES

No XM Sound, But XM Station Information Is Displayed

(Supersedes 10-017, dated August 31, 2010, to revise the information marked by the black bars)

REVISED SUMMARY

SYMPTOM

The sound from the XM radio cuts out or disappears, but the audio unit continues to display the XM station information. The sound returns after the

ignition switch is turned to LOCK (0), then back to ACC (I) or ON (II).

PROBABLE CAUSE

64

There is an internal problem with the XM receiver unit.

VEHICLES AFFECTED

CORRECTIVE ACTION

Replace the XM receiver unit with an updated part.

PARTS INFORMATION

WARRANTY CLAIM INFORMATION

REPAIR PROCEDURE

Replace the XM receiver unit

^ Refer to the Audio section of the appropriate service manual, or

^ Online, under Search by Vehicle, enter keywords REMOVE XM and select the applicable XM RemovalInstallation instructions from the list.

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura Truck MDX V6-3.7L Technical Service Bulletin # 11-014 Date:

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura Truck MDX V6-3.7L Technical Service Bulletin # 11-014 Date:

110617

Electrical - VSA Indicator ON/Multiple DTC's Set

11-014

June 17, 2011

Applies To:

2007-11 MDX - ALL

VSA Indicator or Trailer Stability Assist Warning Is On Intermittently with DTC 59-1, 66-1, 67-1, or 69-1, or Won't Come Out of Park

SYMPTOM

The VSA indicator or the trailer stability assist warning is on with DTCs 59-1, 66-1, 67-1, or 69-1, or you can't move the shift lever out of Park. The

symptoms may be intermittent, and you may not be able to duplicate them after clearing the DTCs.

PROBABLE CAUSE

The brake pedal position switch is malfunctioning.

CORRECTIVE ACTION

Replace the brake pedal position switch.

PARTS INFORMATION

Brake Pedal Position Switch:

P/N 36750-TR2-A01

WARRANTY CLAIM INFORMATION

78

The normal warranty applies.

Operation Number: 7381A2

Flat Rate Time: 0.2 hour

Failed Part: P/N 36750-SJA-013

Defect Code: 03217

Symptom Code: 03205

Skill Level: Repair Technician

REPAIR PROCEDURE

1. Remove the driver's side dashboard undercover:

^ Unlock the dashboard undercover lock knob by turning it 90 degrees.

^ Gently pull down the rear edge of the undercover to detach the clip.

^ Disconnect the footwell light connector and the ambient light connector, then detach the harness clip.

^ Pull the undercover away to release the pins from the holders.

79

2. Unplug the 4P brake pedal position switch connector.

3. Turn the brake pedal position switch counterclockwise 45 degrees and remove it.

4. Remove the old brake pedal position switch insert (green) from the bracket.

5. Install the new brake pedal position switch insert (white) onto the bracket.

NOTE:

The green and white brake pedal position switch inserts are not interchangeable.

80

6. To set the gap of the brake pedal position switch, do this:

^ Lift up on the brake pedal by hand.

^ Push in the brake pedal position switch until its plunger is fully pressed (threaded end touching the pad on the brake pedal arm).

^ Turn the switch clockwise 45 degrees to lock it. The gap between the brake pedal position switch and the pad is automatically adjusted

correctly.

7. Connect the 4P brake position switch connector.

8. Make sure the brake lights go off when the pedal is released.

9. Install the driver's dashboard undercover:

^ Reconnect the harness clip, the ambient light connector, and the footwell light connector.

^ Push up the dashboard undercover to connect the pins to the holders.

^ Gently push up the rear edge of the undercover to reattach the clips.

81

^ Re-lock the lock knob by turning it 90 degrees.

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura Truck RDX AWD L4-2.3L Turbo Technical Service Bulletin # 06-022 Date:

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura TL AWD V6-3.7L Technical Service Bulletin # 11-025 Date:

^ At the online DVD order site, by clicking on the FAQs link (see ORDERING A DVD).***Acura TL AWD V6-3.7L Technical Service Bulletin # 11-025 Date:

110816

Body - Tick/Tapping Noise From R/H Rear Wheelwell Area

11-025

August 16, 2011

Applies To:

2009-12 TL - ALL

Right Rear Wheelwell Area Clicks, Taps, or Ticks

SYMPTOM

The right rear wheelwell area clicks, taps, or ticks.

PROBABLE CAUSE

There is insufficient clearance between the right rear inner wheelwell stiffener and the wheelwell arch.

CORRECTIVE ACTION

Increase the clearance between the right rear wheelwell stiffener and the wheelwell arch.

REQUIRED MATERIALS

3M Ultrapro Urethane Seam Sealer:

3M P/N 051135-08360

WARRANTY CLAIM INFORMATION

73

The normal warranty applies.

Operation Number: 8230D0

Flat Rate Time: 0.6 hour

Failed Part: 64300-TK4-315ZZ

Defect Code: 07403

Symptom Code: 04201

Skill Level: Repair Technician

DIAGNOSIS

Test-drive the vehicle at 20-45 mph over short bumps or uneven road surfaces.

Do you hear a clicking, tapping, or ticking noise from the right rear wheelwell area?

Yes - Go to REPAIR PROCEDURE.

No - This service bulletin does not apply. Continue with normal troubleshooting procedures.

REPAIR PROCEDURE

1. Remove the trunk floor.

74

2. Remove the tool box spacer.

3. Detach the clips, and release the hooks and the tabs by pulling upon the trunk rear trim panel, then remove the panel.

4. Partially remove the trunk lid weatherstrip by pulling it off as needed.

5. Detach the clips and release the Velcro fasteners, then remove the trunk front trim panel.

75

6. Detach the clips and remove the cargo hook buttons, then remove the right trunk side trim panel.

7. Reach through the diamond shaped access hole and force a flat-tipped screwdriver or a pick between the inner wheelwell stiffener and the

wheelwell arch.

8. Separate the two panels to create a gap. Make sure not to separate the two spot welds.

9. Test-drive the vehicle to make sure the noise is gone before sealing the gap and reinstalling the parts.

10. Apply 3M Ultrapro Urethane Seam Sealer to the gap between the inner wheelwell stiffener and the wheelwell arch gap.

11. Reinstall the right side trim panel.

12. Reinstall the front trim panel.

13. Reinstall the trunk lid weatherstrip.

76

NOTE:

Locate the painted alignment mark on the trunk lid weatherstrip. Align the painted mark in the center of the trunk lid opening, and install the

trunk lid weatherstrip all the way around in the direction shown. Make sure there are no wrinkles in the weatherstrip.

14. Reinstall the rear trim panel.

15. Reinstall the tool box spacer.

16. Reinstall the trunk floor.